Home › Сatalogue › Cesspool emptying machine › MVS-10 KAMAZ-43118 Hydraulic washing

Cesspool emptying machine MVS-10 KAMAZ-43118 Hydraulic washing

Purchase

Defer

Capacity	10 cubic meters
Pump:	PNR-124
Pump options:	LC-420, LC-580, PR-150, DL-180/250
Bottom opening:	hydraulic
Lifting the tank:	hydraulic
Chassis:	KAMAZ-43118 (6×6, 300 hp)
Sleeping berth:	unavailable
Equipment:	hydraulic washing Comet
Warranty:	attached implements – 1 year

View complete specification

download PDF

trade-in

Services in equipment
re-equipment

We ensure
worldwide delivery

Specifications

Description

Tanker specifications

Capacity, cubic meter	10
Number of sections	2: under the clean water – 1 cubic meter, for the collection of sludge and waste – 10 cubic meter.
Cross-section form	circle
Steel grade	09Г2С
The thickness of the metal for shells and bottoms	5 mm
Transverse	External
Breakwaters	Internal, hemispherical shape, cold-rolled flanged, offset from the welds of the body, with amplifiers in the lower part, the overlap area is not less than 50%
Structural connection of the tank with the subframe	- Rear hinges (2 PCs.). - Front pressing with a lifting hydraulic cylinder.
Structural connection of the subframe to the chassis frame	The rigid bolt connections, including spring-loaded expansion joints in the front.
Inspection of welds	- Automatic welding of the tank by the robot. - Pressure testing the test pressure. - Ultrasonic testing.
The construction of the subframe	The subframe is made of a 120x80 mm profile in the form of a solid welded structure
Design features	- Lodgments are embedded in the subframe, made in the form of a one-piece structure with a minimum number of welds, - Reinforced attachment of lodgments to the subframe with an increased contact area to give additional rigidity and strength to the entire structure; - Rubber gaskets between the tank and the lodgements; - Lining armor plate on the shell of the tank in the place where it is adjacent to the lodgments to protect the shell from abrasion.
The process vacuum neck is equipped with	A staircase with anti-slip steps and a platform made of slotted anti-slip sheet with a railing for servicing the neck. The stairs and platform are removable and can be replaced or repaired separately from the container.
Lifting the tank	Dump truck type, using one Central front hydraulic cylinder at an angle of at least 40 degrees. The maximum lifting angle of the tank during unloading is limited by a safety valve to prevent the machine from tipping over.
Opening the rear bottom	Up, using two side hydraulic cylinders. Sealing gasket in a circle - MBS. Pressing the bottom with screw clamps – 4 PCs.
Measuring control of tank filling	Float type switch level gauge
Visual inspection of tank filling	Viewing window, spherical (3 PCs.) with illumination, located on the rear bottom, spherical (1 PC.) with illumination, located on the front bottom, Du-120
Materials to the paint tank	- 2-component anticorrosive polyester primer containing zinc phosphate, manufactured by DYO, Turkey. - 2 layers of industrial enamel, manufactured by DYO, Turkey.
The color of the tank	According to the customer's request

Tanker vacuum equipment

Hydraulic washing system for dense soil deposits
Vacuum pump, manufactured by JUROP	- PNR-122, air-cooled blade, capacity 730 cubic meters/hour; - LC-420, vane with liquid cooling and automatic lubrication, capacity 720 cubic meters/hour; - LC-580, vane with liquid cooling and automatic lubrication, capacity 980 cubic meters/hour; - PR-150, vane with forced liquid cooling, capacity 900 cubic meters/hour; - DL-180/250/300, Cam, air-cooled, capacity 1050/1500/1800 cubic meters/hour, respectively.
Pressure-suction hoses	PVC, 2 PCs., DU-100, length 3 m each with quick-release connection Camlock 4”
The dehumidifier is equipped with	- A pressure-vacuum gauge for monitoring the level of underpressure and excess pressure in the tank; - Ball valve for draining water and discharge pipe; - Viewing window for visual control of the water level; The removal of the upper cover is possible without application of lifting mechanisms. The body of the dehumidifier is removable, made of steel 09G2S, 4 mm thick, has a stamped cover and bottom. It can withstand vacuum up to -0.9 kg/cm2.
Pencil cases for sleeves	Metal boxes on both sides of the tank.
Vacuum equipment protection system	- Safety valve for vacuum restriction (-0.9 kg/cm2); - Overpressure safety valve (0.4 kg/cm2).
Tank overflow protection system	- Primary valve in the process neck in the form of a stainless steel ball with a diameter of 150 mm in the basket; - Secondary shut-off valve in the dehumidifier in the form of a stainless steel ball with a diameter of 150 mm in the basket; - Non-contact induction sensor MS-DUG in the neck, which reacts to the approach of the shut-off valve, as a result of which the vacuum pump drive is switched off.
Stop valve	- 4-way valve for switching modes "vacuum creation / pressure injection"; - Knife-type valve on the rear drain with manual drive DU100 with BRS 4” at the lower level of the tank; - Second knife-type valve with manual drive DU100 with BRS4" at 1/3 level for "easy filling" of the tank.
Electrical equipment	- Marker lights on top of the tank in red – 2 PCs. - lighting of the operator's working area (searchlight above the rear drain on top of the tank).
Drain tray	Made of 2 mm thick stainless steel, it has stiffening ribs.
Etc	- rear safety bar to protect the shut-off valve from rear impacts; - aluminum fenders over the rear wheels.
Clean water tanks	Volume=2x0. 5 m3 (communicating). Filling the compartment through the filler neck (top filling) and through the ball valve Du-50 with an adapter to the "Bogdanov" nut in the lower part of the tank (for filling from the hydrant). The filling caps are equipped with UD-1 breathing valves with the appropriate capacity. Equipped with "Column" type level meters
Водяной плунжерный насос высокого давления	Comet TW 13022 S or an analog with a hydraulic drive.
Производительность водяного насоса, л/м	At least 48
Мax давление водяного насоса, МПа (атм.)	12 (120)
Манометр / Водяной фильтр тонкой очистки	At the outlet of the pump / inlet to the pump
Регулировочный клапан	вход
Монитор пистолет с пикой-удлинителем (400 мм) и размывочной форсункой	1 (one) set, RL 124. 120 l/min; 135 bar; inlet 1/2"g; outlet 1/2"g.
Барабан для рукава водяного давления	Inertial, with automatic stacking in an aluminum box
Диаметр / длина рукав высокого давления, мм	D=12 (AGRESSOR), L=15 000
Привод оборудования	Hydraulic, consists of: - Power take-off box "ZF" with double-circuit plate hydraulic pump, - Hydraulic motor, - Set of high-pressure hoses and metal oil pipes, - Multi-position hydraulic distributor with sections with and without latches, - Divertors, - Safety valve, - Oil cooling radiator with thermal sensor (depending on the type of vacuum pump), - expansion hydraulic tank. The drive design allows simultaneous work on hydraulic washing and waste collection in nominal values without loss of pumping equipment power.

KAMAZ-43118 chassis specification

Model
Auxiliary equipment	Towing hitch, Power take off (PTO), Winch (depending on specification)
Brakers
Brake lining width, mm	140
Dimensions: drum Ø, mm	400
Drive	pneumatic
Cab
Configuration	day-cab or sleeper cab (depends on truck configuration)
Type	high or low roof, over the engine (depends on truck configuration)
Characteristic of gvw vehicle
Climbing angle, no less, %	31
Maximum speed, no less, km/h	90
Outer turning radius between walls, m.	11,5–12,9
Clutch
Actuation	hydraulic, with pneumatic booster
Type	diaphragm, single-disk, mod. ZF&SACHS MF 430
Electrical equipment
Batteries, V/A hour	2х12/190
Generator, V/W	28/3000
Voltage, V	24
Engine
Cylinder arrangement and number	V-shaped, 8
Cylinder Ø and piston stroke, mm	120/130
Degree of compression	17
Engine displacement, L	11,76
Fuel feed system	Common Rail
Maximum net horsepower, kW (h. p.)	221 (300)
at crankshaft rotation speed, rpm	1900
Maximum net torque, Nm (kgfm)	1275 (130)
at crankshaft rotation speed, rpm	1300
Model	740.662-300
Type	turbocharged diesel, with aftercooling
Final drive
Ratio	5,94
Transfer case
Control	pneumatic
Type	mechanical, two-speed with interlocking differential
Fuel system
Fuel tank capacity, L	210 or 350 or 210+210 or 350+210 (depending on specification)
Transmission
Control	mechanical, remote control
Gear ratios	1-9,48; 2-6,58; 3-4,68; 4-3,48; 5-2,62; 6-1,89; 7-1,35; 8-1,00; 9-0,75; ЗХ-8,97
Model	ZF 9S1310
Number of gears	9
Weight characteristics and loads
Chassis curb weight, kg	8845...9395 (depending on specification)
Front axle load, kg	4785…5275 (depending on specification)
Rear axle load, kg	3810…4300
Gross combination weight, kg	33600
Gross trailer weight, kg	12000
Gross vehicle with superstructure weight, kg	21600
Rear trailer bogie load, kg	15800
Front axle load, kg	5800
Permissible mass of superstructure with load, kg	12680...12130 (depending on specification)
Wheels and tyres
Rim size	10.00-20 or 12.2-20,9 (depending on specification)
Tyre size	390/95 R20 or 425/85 R21 (depending on specification)
Tyre type	pneumatic, with pressure control
Wheel type	disk wheels

The vacuum silt-sucking machine is designed for collecting municipal waste from the ground surface, from pits and buried tanks, cleaning wells, storm and sewer networks, settling tanks from silt and transporting the collected mass to disposal sites.

MVS-10 can be manufactured in all climatic versions. It is possible to manufacture a tank with an opening bottom or without such a function.

Vehicles are designed for operation on the General network of roads of 1-3 categories (SNiP 11-D5).

Components of the tank:

tank (round section, 09G2S),
vacuum installation (base, pump, oil separator, dehumidifier, pipelines),
hydraulic washing system,
electrical equipment.

Additional equipment:

quick-Release process hatch for tank cleaning.
Additional filler neck at the rear of the tank.
Heating of the gate valve from the engine exhaust system.
Four - way lighting system for the work area.
Tool box of own production on the rear overhang of the car frame.
Technical features of the vacuum machine

Vacuum sludge pump MVS-10 — KAMAZ-43118 car with mounted special equipment placed on it.

Tank vacuum — tank round cross-section. The structure is welded consisting of two bottoms and a shell.

On top of the tank is a neck closed with a lid. The cover has a safety valve, a vacuum valve and a tube for removing air when it is discharged or pressurized. The safety valve is mounted in the neck cover and serves to limit the pressure in the tank. The vacuum valve consists of a cover, a body, and a valve designed to limit vacuuming.

At the rear, at the end of the tank, there is a receiving hatch, which is designed for filling and draining liquid. The hatch is hermetically closed with a lid on which the tap and the pressure head with a plug are fixed.

For convenient maintenance of the tank neck by the operator, there is a service platform made of perforated sheet with anti-slip effect and a lifting ladder.

The tanker is equipped with a pressure-suction sleeve, which is located in the transport position in the pencil case.

Rated voltage in the equipment network is 24 V, direct current from the car network.

Security tool

Placement of the chassis exhaust silencer — according to the chassis configuration.
Fuel tank protection — according to the chassis configuration.
Grounding device — 1 PC. (ground circuit on the bump).
First aid kit — 1 PC.
Anti — rollback stop- 2 PCs. with brackets (ADR p. 8.1.5.2).
Rear protective device (bump) 1 PC. (GOST R 41.58).

Техника в наличии Скачать каталог продукции Получить каталог по почте

Analogs

MVS-5+1 KAMAZ-43253

Purchase

MVS-7,5М KAMAZ-43253

Purchase

AKNS-8 (+1) KAMAZ-53605

Purchase

Purchase

Purchase

Purchase

Purchase

MVS-10+2 KAMAZ-43118 Cummmins

Purchase

MVS-10M KAMAZ-65115

Purchase

AKNS-10 KAMAZ-65115 АТЕХ

Purchase

yet 8 items

Программа TRADE-IN от производителя. Обмен старого автомобиля на новый Камаз.

Выгодно:

Принимаются грузовики любых производителей, без ограничений, в качестве первоначального взноса
Автомобили закупаются напрямую у владельцев
Ценовое предложение на подержанный грузовик в течении суток
Оптимальная цена на рынке за Ваш грузовик с пробегом
Надежность и гарантия юридической чистоты сделки

Удобно:

Предварительный осмотр и ценовое предложение по фотографиям
Комплексная диагностика сдаваемого грузовика силами сервисного центра
Выбор нового автомобиля у официального дилера ПАО «КАМАЗ»
Заключение договора обратного выкупа

Программа действует как для юридических так и для физических лиц.

Услуги по дооборудованию и доработке

Выполним необходимые клиенту доработки и оснастим технику дополнительным оборудованием.

Наши специалисты выполнят:

дооборудование для перевозки ГСМ;
доработки для эксплуатации в экстремально холодных условиях;
дооснащение автономными подогревателями;
монтаж кондиционеров;
установку тахографов;
монтаж дополнительных топливных баков;
доработки кабины: утепление, увеличение размера, оснащение спальным местом;
а также многое другое. К полному списку доработок...

Shipping

Delivery methods

Delivery to the CIS countries by road or rail.

Delivery to other foreign countries: marine and aircraft transport,
railway transport.

Shipping terms

If products are in stock, we can perform shipment within 3 days.
If the necessary equipment is not available, the shipment will be made within the period from 10 to 15 calendar days.

Payment

Payment methods