Pump unit SIN-32 on KAMAZ-43118 designed for well cementing, pressure testing, washover and squeezing jobs in oil and gas wells.
The unit can be used as a diagonal-axis charging pump capable to pump viscous fluids with abrasive inclusions.
Tanker capacity: | 6 cubic meter |
Pump: | SIN-32, triplex plunger pump |
Plungers: | 100 and 125 mm |
Water feedingмpump: | CNS 38-154 |
Chassis: | KAMAZ-43118 (6×6, 280/300 hp, E-4) |
Producer: | Sinergiya |
Tanker capacity, cubic metes | 6 |
---|---|
High pressure triplex plunger pump | SIN-32 cementing, triplex plunger pump , horizontal with two-speed reduction gear |
Plunger diameter, mm | 100, 125 |
Peak pressure, MPa, (at pump capacity, L/sec) - at plunger diameter 100 mm - at plunger diameter 125 mm |
50 (2,3) 32 (3,7) |
Max theoretical capacity, L/sec (m3/h) - at plunger diameter 100 mm 10,4 MPa - at plunger diameter 125 mm 6,6 MPa |
11,5 (41,4) 18 (64,8) |
Useful output, kW | 176 |
Pump drive | Chassis additional engine dependent PTO |
Pumped solution density, kg/cubic meter | 1000–2100 |
Model | CNS 38-154 |
---|---|
Centrifugal pump drive | Diesel, D 120 |
Peak pressure, MPa | 1,2 |
Max pump capacity, L/sec | 8,3 |
Model | |
---|---|
Auxiliary equipment | Towing hitch, Power take off (PTO), Winch (depending on specification) |
Brakers | |
Brake lining width, mm | 140 |
Dimensions: drum Ø, mm | 400 |
Drive | pneumatic |
Cab | |
Configuration | day-cab or sleeper cab (depends on truck configuration) |
Type | high or low roof, over the engine (depends on truck configuration) |
Characteristic of gvw vehicle | |
Climbing angle, no less, % | 31 |
Maximum speed, no less, km/h | 90 |
Outer turning radius between walls, m. | 11,5–12,9 |
Clutch | |
Actuation | hydraulic, with pneumatic booster |
Type | diaphragm, single-disk, mod. ZF&SACHS MF 430 |
Electrical equipment | |
Batteries, V/A hour | 2х12/190 |
Generator, V/W | 28/3000 |
Voltage, V | 24 |
Engine | |
Cylinder arrangement and number | V-shaped, 8 |
Cylinder Ø and piston stroke, mm | 120/130 |
Degree of compression | 17 |
Engine displacement, L | 11,76 |
Fuel feed system | Common Rail |
Maximum net horsepower, kW (h. p.) | 221 (300) |
at crankshaft rotation speed, rpm | 1900 |
Maximum net torque, Nm (kgfm) | 1275 (130) |
at crankshaft rotation speed, rpm | 1300 |
Model | 740.662-300 |
Type | turbocharged diesel, with aftercooling |
Final drive | |
Ratio | 5,94 |
Transfer case | |
Control | pneumatic |
Type | mechanical, two-speed with interlocking differential |
Fuel system | |
Fuel tank capacity, L | 210 or 350 or 210+210 or 350+210 (depending on specification) |
Transmission | |
Control | mechanical, remote control |
Gear ratios | 1-9,48; 2-6,58; 3-4,68; 4-3,48; 5-2,62; 6-1,89; 7-1,35; 8-1,00; 9-0,75; ЗХ-8,97 |
Model | ZF 9S1310 |
Number of gears | 9 |
Weight characteristics and loads | |
Chassis curb weight, kg | 8845...9395 (depending on specification) |
Front axle load, kg | 4785…5275 (depending on specification) |
Rear axle load, kg | 3810…4300 |
Gross combination weight, kg | 33600 |
Gross trailer weight, kg | 12000 |
Gross vehicle with superstructure weight, kg | 21600 |
Rear trailer bogie load, kg | 15800 |
Front axle load, kg | 5800 |
Permissible mass of superstructure with load, kg | 12680...12130 (depending on specification) |
Wheels and tyres | |
Rim size | 10.00-20 or 12.2-20,9 (depending on specification) |
Tyre size | 390/95 R20 or 425/85 R21 (depending on specification) |
Tyre type | pneumatic, with pressure control |
Wheel type | disk wheels |
Pump unit SIN-32 on KAMAZ-43118 designed for well cementing, pressure testing, washover and squeezing jobs in oil and gas wells.
The unit can be used as a diagonal-axis charging pump capable to pump viscous fluids with abrasive inclusions.